Creston has designed the CP2E media control primarily for small to medium environments in commercial and private sectors. As connections are three COM ports, eight IR / serial ports, eight I / O Versiports, eight isolated relays and an Ethernet connection is available. For projectors, DVD players, screens and much more can be controlled.
Optionally, the CP-2E control system of Creston can be equipped with the Cresnet expansion modules, to obtain additional control connections. A powerful 32-bit Freescale Coldfire processor and real-time operating system, making the unit as a whole to one of the fastest and most reliable media controls that are available.
Using the integrated network port, the CP2E control system , you have a variety of options, in terms of remote access, monitoring, diagnostics and programming. Optionally, you assign a static or dynamic IP address for media control and get then to access, the embedded Web server and e-mail client. With regard to the administration but can equally well the SNMP protocol can be used.
Another feature of the CP-2E media control from Crestron , is the so-called slave mode. This allows you to configure the system as an expansion module Cresnet and can extend an existing control system, creating a cost-effective and flexible solution is provided.
Processor | ||
CPU | 32-bit Freescale ColdFire Microprocessor | |
Memory | ||
SDRAM | 32MB | |
NVRAM | 256 KB | |
Flash | 4 MB | |
Operating System | ||
Real-time, preemptive multi-threaded / multitasking kernel; FAT32 file system with long names; supports SIMPL ™ Windows® and SIMPL + | ||
Ethernet | ||
10 / 100BaseT, auto-negotiating, full / half duplex, static IP or DHCP / DNS, SSL, TCP / IP, UDP / IP, CIP, SMTP, SNMP, Web server and built-in e-mail client; supports Crestron e-Control 2 and RoomView XPanel applications | ||
Connectors | ||
COM A - C | (3) DB9 male, bidirectional RS-232/422/485 ports; Up to 115.2k baud; Hardware and software handshaking support; All ports support C2N-NPA8 Network Poll Accelerator | |
INFRARED-SERIAL OUTPUT A - H | (8) 2-pin 3.5mm detachable terminal blocks, IR / Serial Output Ports; IR output up to 1.2 MHz; 1-way serial TTL / RS-232 (0-5 Volts) up to 115.2k baud; Individual signal generator per port, Allowing simultaneous firing of all ports | |
I / O Versiports 1-8 | (1) 9-pin 3.5mm detachable terminal block Comprising (8) digital input / output or analog input ports (referenced to GND); Digital Input: Rated for 0-24 Volts DC, input impedance 20k ohms, Logic Threshold 1:24 Volts DC; Digital Output: 250mA sink from maximum 24 Volts DC, catch diodes for use with & ldquo; real world & quot; loads; Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC maximum input impedance 20k ohms; Programmable 5 Volts, Ohms 2k pull-up resistor by pin | |
RELAY OUTPUT 1-8 | (2) 8-pin 3.5mm detachable terminal block Comprising (8) normally open, isolated relays; Rated 1 Amp, 30 Volts AC / DC; MOV arc suppression across contacts | |
LAN | (1) 8-wire RJ45 with 2 LED indicators; 10 / 100BaseT Ethernet port; Green LED indicates link status; Yellow LED indicates Ethernet activity | |
COMPUTER | (1) DB9 female, RS-232 computer console port | |
NET | (1) 4-pin 5mm detachable terminal block; Cresnet port, Master / Slave selectable; Expandable via C2N-NPA8 Network Poll Accelerator | |
24VDC | (1) 2.1mm barrel DC power jack, 24 Volt DC power input; (& Gt; PW-2420RU power supply sold separately); Pass through to NET port to power Cresnet Devices | |
Reset Button | ||
HW-R | Hardware reset (reboots the control system) | |
SW-R | Software reset (restarts the SIMPL program) | |
LED Indicators | ||
PWR | (1 green) Indicates DC Power Supplied to unit | |
NET | (1 yellow) Indicates Cresnet bus activity | |
MSG | (1 red) Indicates control system has generated an error message | |
lnk | (1 red) Indicates a valid connection on LAN port | |
ACT | (1 red) Indicates activity on LAN port | |
Power Requirements | ||
24 Watts (1 Amp) @ 24 Volts DC (PW-2420RU power supply sold separately) | ||
Available Cresnet Power | 26 Watts using PW-2420RU (sold separately) | |
Cresnet Power Usage | 24 Watts (1 Amp @ 24 Volts DC) with no power supply connected to the 24VDC connector | |
delivery | 1x CP2E, 1x power supply, other accessories not included |